Parts for Aquabot Aquamax Bi-Turbo Robotic pool cleaner,Aquamax Bi-Turbo parts,discount Aquabot Aquamax Bi-Turbo pool cleaner parts

Aquabot AquaMax Bi-Turbo Swimming Pool Cleaner Parts

Aquabot Aqua Max Pool Cleaner Parts, Parts for Aquabot Aquamax Bi Turbo Pool Cleaners
Schematic Diagram of Parts for Aquabot AquaMax Bi-Turbo Robotic Pool Cleaner

NLA - No Longer Available Cells

No.	Item No.	Description	Price
1	A10201	Handle Assembly (Blue & White, Bracket included) -Aquabot Ultra, AquaMax	$145.22
1	A10203	Handle Assembly (Blue & White, Bracket Included) -AquaMax BiTurbo, Ultramax Junior	$125.61
2	S1100B	Handle Bracket (Blue) -All Aquabot Except T2 and T4, All AquaMax, All Ultramax cleaners listed	$35.38
4	11003	Clevis Pin (Round Head, Hole in end) -Use to link the Handle Assembly arm to the Handle Bracket	$4.08
6	11004	Washer (St. Steel) -Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket	$2.19
7	11005	Cotter Ring (Aluminum, 3/16") -Use at end of the Clevis Pin to hold the Handle Bracket	$2.98
8	1105	Screw (10-32, 7/8", Phil Pan Head) -Use to fasten the Handle Bracket to the Body Assembly	$1.95
10	2500	Screw (#8, 1-1/4" Pan Head) -Use on Back Plate Block, and for White Drive Motors through Handle Assembly	$1.82
12	2100	P-Clip (1/4", Plastic) -Use to fasten the non-insulated part of a 2-wire cable to the Body	$2.20
12	2101	P-Clip (5/16", Plastic) -Use to fasten the non-insulated part of a 4-wire cable to the Body	$1.82
12	2104	P-Clip (3/8", Plastic) -Use to fasten the foam-insulated part of a 2-wire cable to the body	$1.82
12	2102	P-Clip (7/16", Plastic) -Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly	$1.82
12	8316	P-Clip (9-16" Plastic) -Use to fasten the Heat Shrink part of the 2-wire cable to the Handle Assembly	$1.87
12	2110	P-Clip (5/8", St. Steel) -Use to fasten the foam-insulated part of a 4-wire cable to the Handle Assembly	$3.58
12	2111	P-Clip (5/8", Coated Steel) -Use to fasten the insulated part of a 4, 7, 9-wire cable to the Handle Assembly	$3.49
13	2700	Screws (#8, 11/16", Phil Pan - Flat Head) -Use to fasten P-Clips, Side Plates, and Drive Motor	$1.82
14	2260	Screws (#6, 7/16", Phil Pan - Flat Head) -Use to fasten P-Clips, and Side Plates on Jet and Rover Cleaners	$1.95
15	1601	Plug (3-Pin, Female, 2-Wire) -Aquabot / AquaMax / AquaMax Jr.	$16.75
15	1635	Plug (4-Pin, Female, 4-Wire) -Aquabot Turbo RC / AquaMax	$48.40
15	1636	Plug (7-Pin, Female, 7-Wire) -Aquabot / AquaMax	$48.40
16	S7930	EZ-Swivel (For 2-Wire Cable) -Can be used on any 2-wire Cable Assembly	$60.79
16	S7935	EZ-Swivel (For 4, 5, 7, or 9-Wire Cable) -Can be used on any Cable Assembly with 4 or more wires	$60.79
17	A17121	Cable Assembly (2-Wire, 120 Foot, Floating) -AquaMax	$591.98
17	A16122	Cable Assembly (4-Wire, 120 Foot, Floating) -AquaMax BiTurbo	$709.27
17	A16119	Cable Assembly (7-Wire, 120 Foot, Floating) -AquaMax Junior Plus RC, AquaMax BiTurbo RC	$709.27
25	2230B	Outlet Top (Top and Bottom) -Aquabot, AquaMax / Jr. / BiTurbo	$39.84
26	A22201	Body Assembly (White, with Lock Tabs, Outlet Ring, Inserts) -AquaMax	NLA	No Longer Available
26	A22201AMXSOLO	Body Assembly (White, with Lock Tabs, Outlet Ring, Inserts) -AquaMax Solo, AquaMax Remote Control	NLA	No Longer Available
26	A22201MBT	Body Assembly (White, with Lock Tabs, Outlet Rings, Inserts) -AquaMax BiTurbo	$218.95
26	A22201MBTSOLO	Body Assembly (White, with Lock Tabs, Outlet Rings, Inserts) -AquaMax BiTurbo Solo, AquaMax BiTurbo RC	NLA	No Longer Available
---	8351	Flat Plug (White, Plastic) -Use to plug large holes on the Body Assembly	$1.87
27	2251	Screw (8-18 x 3/4, Phil Small Head) -Use for Pump to Body in some cleaners, and Jet Valve Assembly	$1.82
29	SP2300	Anti-Roll Brackets (Plastic, White) -Aquabot / Turbo/ Plus RC/ Ultra, AquaMax / Jr. BiTurbo	$13.57
---	2400	Nail Plug (White, Plastic) -Use to plug small holes on the Body Assembly	$1.87
30	SP3402	Lock-Nuts (Hex, Nylon insert) -For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly	NLA	No Longer Available
31	2261	Screw (M-5, Phil Bev Head) -Use to fasten the Anti-Roll Brackets to the Body Assembly	$1.82
36	SP9204BL	Lock-Tabs (Blue, Plastic) -For all Body Assemblies, used to hold Bottom Lids to base of cleaners	$5.15
38	2303	Screws (18-8, 8/32" x 1/2", Phil Bev Head) -Use to fasten the Lock-Tabs to the Body Assembly	$1.82
39	7133	Lock-Nut (Nylon Insert, Hex) -Use to fasten the Screws of the Lock-Tabs	$3.30
45	S3400B-8H	Side Plate (Blue, 8 Holes: 4 Bolts, 4 Piston Clamps)	$31.42
45	S3400B-6H	Side Plate (Blue, 6 Holes: 4 Bolts, 2 Motor)	$31.42
49	3401	Screw (Bolts, Long, For Side Plate)	$13.82
51	2600PK	Bushing (White, Plastic) - Pack of 4	$13.46
52	2610	Bushing (White, Plastic) -Use for Pin on Body Assembly - Aquabot/ Turbo, All AquaMax	$6.35
54	3500	Small Roller (White, Plastic) -Supports the Drive Track, install on lower legs of Side Plate	$3.86
55	3700	Large Roller (White Plastic) -Supports the Drive Track, installs on Body Assembly Pin Support	$5.76
56	3506	Stepped Sleeve Roller (White) -Thicker end supports Drive Belts, Install on upper Side Plate legs	$3.95
57	SP3302	Drive Belts (Tan)	$19.51
58	A3600	Pulley Assembly (Short, ~ 2.5 in.) -Use for cleaners with White Drive Motors	$28.99
58	A3605	Pulley Assembly (Medium, ~ 2.75 in.) -Use for cleaners with Black Drive Motor	$35.04
---	3607	Washer -Use on all Pulley Assemblies, Rounded edges facing inward	$7.37
---	SP3502	Tension Device (OLD, Replaced by Stepped Sleeve Rollers) -Formerly used to add Tension to Drive Belts	$38.62
60	A6010U	Pump Motor	NLA	No Longer Available
61	4400	Propeller - All Cleaners	$14.13
65	A2207	DC Pump Filter (White, Plastic)	$55.46
66	300099	Tubing (Clear PVC, 5/16" ID x 7/16" OD) -Use to divert water from the DC Pump Filter to the DC Pump	$1.59
67	700038	Spacer Block (Grey, Stepped Shape) -Use to position the Piston apart from the Model G Drive Tracks	$12.12
68	S300092	DC Pump Motor (Single, no Gate, 2-Wire) -Aquabot Turbo Solo, All AquaMax Solo/ IR cleaners	$78.86
68	S300093	DC Pump Motor (Dual, with Gate, 2-Wire) -Aquabot Turbo RC, Aquabot T4, All AquaMax RC cleaners	$78.86
69	300111	Tubing (Clear PVC, 3/16" ID x 5/16" OD) -Use to divert water from the DC Pump to the Piston Assembly	NLA	No Longer Available
70	300109	Clamp (Grey, Plastic, Narrow)	NLA	No Longer Available
70	300108	Clamp Bracket (Grey, Plastic, Wide)	$3.24
71	300107	Back Plate Block (Grey, 4 Holes) -Use to support the DC Pump Motor inside of the Body Assembly	NLA	No Longer Available
72	SP6204	Spacer (Plastic, Cylinder) -Use to make space between the Back late Block and the Body Assembly	NLA	No Longer Available
73	1107	Screw (10-32, 1-3/4" Phil Pan Head) -Use to fasten Clamp & Piston onto Side Plate of a Model G cleaner	$1.74
73	2301	Screw (10-32, 1/2" Phil Pan Head) -Use with Clamp to fasten Piston t Side Plate and DC Pump to Block	NLA	No Longer Available
75	7109	Washer (St. Steel) -Use with #2500 Screw against Body Assembly to fasten Back Plate Bock to Body	$2.20
77	S300090	Piston Assembly (White, Plastic) -One Piston is used for Solo Cleaners, Two are used for RC cleaners	$69.02
78	300084	Rubber Tip (White, Rubber) -Use at the bottom of the plunger of the Piston Assembly	$3.12
80	A8511IR	Drive Motor (Black, Bare Wire Leads) -AquaMax IR, AquaMax BiTurbo IR	$634.26
80	A8517MBT	Drive Motor (Black, Bare Wire Leads) -AquaMax, AquaMax RC, AquaMax BiTurbo RC	$634.26
80	A8516MBTS	Drive Motor (Black, Bare Wire Leads) -AquaMax Solo, AquaMax BiTurbo Solo	$634.26
83	4613	Spiral Pin (3/4", Solid Stainless Steel) -Used in the end of the Drive Motor Shaft, use Lock-Tite	$1.82
86	SP5474	Shrinkable Butt Connectors (Light Blue) -Crimp closed and heat shrink to seal	$3.64
87	SP1617	Shrink Tube (5/16", Blue) -For sealing 2-wire connections, use under Heat Shrink 1619	$48.32
87	SP1619	Shrink Tube (1/2", Black) -For sealing 2-wire connections, use over Heat Shrink 1617	NLA	No Longer Available
---	SP1611	Shrink Tube (3/4", Blue) -For sealing the Cable insulation below the P-Clip at the Handle Assembly	NLA	No Longer Available
---	A38001	Wheel Tube Assembly (Old, AquaMax, AquaMax BiTurbo)	$76.92
90	A38001MG	Wheel Tube Assembly (New, AquaMax, AquaMax BiTurbo) -Model 'G'	$75.05
91	11058	Retaining Ring (E-Clip, New Style)	$2.78
92	3603	Washer (Nylon, Flat) -Use for all cleaners on the end of Wheel or Wheel Tube Assembly	$1.82
97	SPA2901	Sponge Brushes (Black Sponge Foam, Long) -AquaMax, AquaMax BiTurbo	$81.57
97	SP3002BM	Rubber Brushes (Blue Molded Rubber, Long) -AquaMax, AquaMax BiTurbo, PHV200	$85.22
97	SP3003M	Rubber Brushes (Black Molded Rubber, Long) -AquaMax, AquaMax BiTurbo	$87.35
97	SP3008	PVA Climbing Brushes (Light Blue PVA Foam, Long) -AquaMax, AquaMax BiTurbo	$139.34
---	SP3007	PVA Climbing Rings (Light Blue PVA, 1" Thick) -Fit over Rubber Brushes to add more traction**	$28.38
99	3200	Drive Track (Black)	$23.51
99	3201	Drive Track (Blue)	$24.97
99	3203	Drive Track with Traction Tabs (Blue) -For all Model 'G' units - Single	$24.97
100	SP2675	Model 'G' Spacer Brackets -** necessary with 'Model G' Drive Tracks	$6.17
101	8101	Filter Bag (Fine)	$74.60
101	8201	Filter Bag (Mesh)	$72.32
102	SP8001	Filter Bag Clip (Black, Plastic)	$11.14
103	5301	Filter Screen (White, Cage)	$35.28
104	2702	Screw (#6, 11/16", Phil Pan - Flat Head, Pointed) -For fastening the 5300/ 5301 Filter Screen to the Body	$1.95
105	A9201XC	Bottom Lid Assembly (White, Square Wire Frame)	$117.92
107	9301	Intake Valve Flap (Black PVC Rubber)	$3.49
108	S3103	H-Float (Foam, Plastic, with Screws) -Fasten to Bottom Lid if cleaner's wall-climbing is not high enough	$13.42
---	SP5173	Weights (Black) -Put in Bottom Lid if cleaner's wall-climbing is too high	$8.71
109	SP3104	Side Pocket Floats (White, Foam Blocks) -Put in Bottom Lid if wall-climbing is not high enough	$5.17
110	7063C	Power Supply (3-Prong, Male Socket)	$349.19
110	A7082	Power Supply (4-Prong, Male Socket)	$533.54
110	A7065	Power Supply (4-Pin, Male Socket)	$406.05
110	A7064	Power Supply (7-Pin, Male Socket, Radio RC)	$404.33
111	7108	Socket Assembly (3-Pin, Male, 2-Wire)	$12.10
111	7135	Socket Assembly (4-Pin, Male, 4-Wire)	$35.28
111	7136	Socket Assembly (7-Pin, Male, 7-Wire)	$36.18
---	7163E	Dust Cap (Old, Plastic, Threaded, Chained)	$1.74
112	7005	Fuse Holder (Standard, Rush & Turn Style) -Most Residential and Commercial cleaners	$10.28
112	7205	Fuse Holder (Alternate, Phillips Head Style) -Only when specified by Aqua Products Service	$10.91
112	7206	Fuse Holder (Mini, Phillips Head Style) -Use for all Power Supplies with Dial Timers	$10.28
---	7002	Fuse (5.0 Amp, 250 Volt, Slow-Blow) -Aquabot Plus RC, Aquabot Ultra, All AMAX, All UMAX, All PHV	$4.69
---	7207	Fuse (3 AMP, Mini, 250 Volt, Slow-Blow) -New Aquabot Plus RC and Aquabot Ultra	$4.26
114	7106	On/ Off Lighted Switch (Wide, Standard, Red, 3-Wire) -Use for Power Supply	$11.14
115	7024	Antenna (4", with Hardware) -AquaMax Jr. Plus RC, AquaMax RC, AquaMax BiTurbo RC	$13.44
---	A220200KIT	RC Kit - Includes matched 220117c Radio TC Transmitter (Grey/ Yellow face) and A220200FCC Receiver	NLA	No Longer Available
---	A220200FCC	Receiver (Radio, 2-Way) - New Units Only -Responds to 220117C Transmitter - Older units will need to order Kit above	NLA	No Longer Available
116	220117C	Transmitter (Radio RC, Grey & Yellow/ Blue/ Red LED Light) -New Units Only - Transmits to A220200FCC Receiver - Older Units will need Kit	NLA	No Longer Available
117	7041A	Handle (Plastic, with Hardware) -Use on All Power Supplies except Ultramax	$7.86
118	7102	Cord for Power Supply (3-Wire, Green, Black, and White) -Use on all Power Supplies	$13.53
119	7272	Outdoor Timer (8hr, Programmable, GFCI) -Use to regulate cleaner's run time when no Auto shut-off	$49.23
---	2209	Infra Red Sensor	$170.37
---	2009	IR Brace Assembly (all hardware included) -Use to hold the IR Sensor in position on the cleaner	$24.17
---	2008	Screws (Use to hold IR Brace inside of Outer Shell) -Screw from outside of shell into IR Brace Assembly	NLA	No Longer Available
---	1609	Tie (Blue, #4 Plastic, Reusable) -Use for coiling the Cable Assembly among other things	NLA	No Longer Available
---	A800135	Main Drain Bumper -Can be used on most Pools' Main Drain, where a cleaner may get stuck	$42.80

All Aqua Max Cleaner Parts are Original Aquabot Replacement Parts, and spares for the Aquabot pool cleaner
To purchase more than 1 Aquabot AquaMax Bi-Turbo Bi Turbo part, hit the		button in the Shopping Cart


	Return to POOLCENTER.com's Swimming Pool Cleaner Parts Main Page

Aquabot AquaMax Bi-Turbo Swimming Pool Cleaner Parts

Aquabot Aqua Max Pool Cleaner Parts, Parts for Aquabot Aquamax Bi Turbo Pool Cleaners Schematic Diagram of Parts for Aquabot AquaMax Bi-Turbo Robotic Pool Cleaner

A10201

Handle Assembly (Blue & White, Bracket included) -Aquabot Ultra, AquaMax

A10203

Handle Assembly (Blue & White, Bracket Included) -AquaMax BiTurbo, Ultramax Junior

S1100B

Handle Bracket (Blue) -All Aquabot Except T2 and T4, All AquaMax, All Ultramax cleaners listed

11003

Clevis Pin (Round Head, Hole in end) -Use to link the Handle Assembly arm to the Handle Bracket

11004

Washer (St. Steel) -Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket

11005

Cotter Ring (Aluminum, 3/16") -Use at end of the Clevis Pin to hold the Handle Bracket

1105

Screw (10-32, 7/8", Phil Pan Head) -Use to fasten the Handle Bracket to the Body Assembly

2500

Screw (#8, 1-1/4" Pan Head) -Use on Back Plate Block, and for White Drive Motors through Handle Assembly

2100

P-Clip (1/4", Plastic) -Use to fasten the non-insulated part of a 2-wire cable to the Body

2101

P-Clip (5/16", Plastic) -Use to fasten the non-insulated part of a 4-wire cable to the Body

2104

P-Clip (3/8", Plastic) -Use to fasten the foam-insulated part of a 2-wire cable to the body

2102

P-Clip (7/16", Plastic) -Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly

8316

P-Clip (9-16" Plastic) -Use to fasten the Heat Shrink part of the 2-wire cable to the Handle Assembly

2110

P-Clip (5/8", St. Steel) -Use to fasten the foam-insulated part of a 4-wire cable to the Handle Assembly

2111

P-Clip (5/8", Coated Steel) -Use to fasten the insulated part of a 4, 7, 9-wire cable to the Handle Assembly

2700

Screws (#8, 11/16", Phil Pan - Flat Head) -Use to fasten P-Clips, Side Plates, and Drive Motor

2260

Screws (#6, 7/16", Phil Pan - Flat Head) -Use to fasten P-Clips, and Side Plates on Jet and Rover Cleaners

1601

Plug (3-Pin, Female, 2-Wire) -Aquabot / AquaMax / AquaMax Jr.

1635

Plug (4-Pin, Female, 4-Wire) -Aquabot Turbo RC / AquaMax

1636

Plug (7-Pin, Female, 7-Wire) -Aquabot / AquaMax

S7930

EZ-Swivel (For 2-Wire Cable) -Can be used on any 2-wire Cable Assembly

S7935

EZ-Swivel (For 4, 5, 7, or 9-Wire Cable) -Can be used on any Cable Assembly with 4 or more wires

A17121

Cable Assembly (2-Wire, 120 Foot, Floating) -AquaMax

A16122

Cable Assembly (4-Wire, 120 Foot, Floating) -AquaMax BiTurbo

A16119

Cable Assembly (7-Wire, 120 Foot, Floating) -AquaMax Junior Plus RC, AquaMax BiTurbo RC

2230B

Outlet Top (Top and Bottom) -Aquabot, AquaMax / Jr. / BiTurbo

A22201

Body Assembly (White, with Lock Tabs, Outlet Ring, Inserts) -AquaMax

A22201AMXSOLO

Body Assembly (White, with Lock Tabs, Outlet Ring, Inserts) -AquaMax Solo, AquaMax Remote Control

A22201MBT

Body Assembly (White, with Lock Tabs, Outlet Rings, Inserts) -AquaMax BiTurbo

A22201MBTSOLO

Body Assembly (White, with Lock Tabs, Outlet Rings, Inserts) -AquaMax BiTurbo Solo, AquaMax BiTurbo RC

8351

Flat Plug (White, Plastic) -Use to plug large holes on the Body Assembly

2251

Screw (8-18 x 3/4, Phil Small Head) -Use for Pump to Body in some cleaners, and Jet Valve Assembly

SP2300

Anti-Roll Brackets (Plastic, White) -Aquabot / Turbo/ Plus RC/ Ultra, AquaMax / Jr. BiTurbo

2400

Nail Plug (White, Plastic) -Use to plug small holes on the Body Assembly

SP3402

Lock-Nuts (Hex, Nylon insert) -For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly

2261

Screw (M-5, Phil Bev Head) -Use to fasten the Anti-Roll Brackets to the Body Assembly

SP9204BL

Lock-Tabs (Blue, Plastic) -For all Body Assemblies, used to hold Bottom Lids to base of cleaners

2303

Screws (18-8, 8/32" x 1/2", Phil Bev Head) -Use to fasten the Lock-Tabs to the Body Assembly

7133

Lock-Nut (Nylon Insert, Hex) -Use to fasten the Screws of the Lock-Tabs

Aquabot Aqua Max Pool Cleaner Parts, Parts for Aquabot Aquamax Bi Turbo Pool Cleaners
Schematic Diagram of Parts for Aquabot AquaMax Bi-Turbo Robotic Pool Cleaner

Handle Assembly (Blue & White, Bracket included)
-Aquabot Ultra, AquaMax

Handle Assembly (Blue & White, Bracket Included)
-AquaMax BiTurbo, Ultramax Junior

Handle Bracket (Blue)
-All Aquabot Except T2 and T4, All AquaMax, All Ultramax cleaners listed

Clevis Pin (Round Head, Hole in end)
-Use to link the Handle Assembly arm to the Handle Bracket

Washer (St. Steel)
-Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket

Cotter Ring (Aluminum, 3/16")
-Use at end of the Clevis Pin to hold the Handle Bracket

Screw (10-32, 7/8", Phil Pan Head)
-Use to fasten the Handle Bracket to the Body Assembly

Screw (#8, 1-1/4" Pan Head)
-Use on Back Plate Block, and for White Drive Motors through Handle Assembly

P-Clip (1/4", Plastic)
-Use to fasten the non-insulated part of a 2-wire cable to the Body

P-Clip (5/16", Plastic)
-Use to fasten the non-insulated part of a 4-wire cable to the Body

P-Clip (3/8", Plastic)
-Use to fasten the foam-insulated part of a 2-wire cable to the body

P-Clip (7/16", Plastic)
-Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly

P-Clip (9-16" Plastic)
-Use to fasten the Heat Shrink part of the 2-wire cable to the Handle Assembly

P-Clip (5/8", St. Steel)
-Use to fasten the foam-insulated part of a 4-wire cable to the Handle Assembly

P-Clip (5/8", Coated Steel)
-Use to fasten the insulated part of a 4, 7, 9-wire cable to the Handle Assembly

Screws (#8, 11/16", Phil Pan - Flat Head)
-Use to fasten P-Clips, Side Plates, and Drive Motor

Screws (#6, 7/16", Phil Pan - Flat Head)
-Use to fasten P-Clips, and Side Plates on Jet and Rover Cleaners

Plug (3-Pin, Female, 2-Wire)
-Aquabot / AquaMax / AquaMax Jr.

Plug (4-Pin, Female, 4-Wire)
-Aquabot Turbo RC / AquaMax

Plug (7-Pin, Female, 7-Wire)
-Aquabot / AquaMax

EZ-Swivel (For 2-Wire Cable)
-Can be used on any 2-wire Cable Assembly

EZ-Swivel (For 4, 5, 7, or 9-Wire Cable)
-Can be used on any Cable Assembly with 4 or more wires

Cable Assembly (2-Wire, 120 Foot, Floating)
-AquaMax

Cable Assembly (4-Wire, 120 Foot, Floating)
-AquaMax BiTurbo

Cable Assembly (7-Wire, 120 Foot, Floating)
-AquaMax Junior Plus RC, AquaMax BiTurbo RC

Outlet Top (Top and Bottom)
-Aquabot, AquaMax / Jr. / BiTurbo

Body Assembly (White, with Lock Tabs, Outlet Ring, Inserts)
-AquaMax

Body Assembly (White, with Lock Tabs, Outlet Ring, Inserts)
-AquaMax Solo, AquaMax Remote Control

Body Assembly (White, with Lock Tabs, Outlet Rings, Inserts)
-AquaMax BiTurbo

Body Assembly (White, with Lock Tabs, Outlet Rings, Inserts)
-AquaMax BiTurbo Solo, AquaMax BiTurbo RC

Flat Plug (White, Plastic)
-Use to plug large holes on the Body Assembly

Screw (8-18 x 3/4, Phil Small Head)
-Use for Pump to Body in some cleaners, and Jet Valve Assembly

Anti-Roll Brackets (Plastic, White)
-Aquabot / Turbo/ Plus RC/ Ultra, AquaMax / Jr. BiTurbo

Nail Plug (White, Plastic)
-Use to plug small holes on the Body Assembly

Lock-Nuts (Hex, Nylon insert)
-For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly

Screw (M-5, Phil Bev Head)
-Use to fasten the Anti-Roll Brackets to the Body Assembly

Lock-Tabs (Blue, Plastic)
-For all Body Assemblies, used to hold Bottom Lids to base of cleaners

Screws (18-8, 8/32" x 1/2", Phil Bev Head)
-Use to fasten the Lock-Tabs to the Body Assembly

Lock-Nut (Nylon Insert, Hex)
-Use to fasten the Screws of the Lock-Tabs

Bushing (White, Plastic)
-Use for Pin on Body Assembly - Aquabot/ Turbo, All AquaMax

Small Roller (White, Plastic)
-Supports the Drive Track, install on lower legs of Side Plate

Large Roller (White Plastic)
-Supports the Drive Track, installs on Body Assembly Pin Support

Stepped Sleeve Roller (White)
-Thicker end supports Drive Belts, Install on upper Side Plate legs

Pulley Assembly (Short, ~ 2.5 in.)
-Use for cleaners with White Drive Motors

Pulley Assembly (Medium, ~ 2.75 in.)
-Use for cleaners with Black Drive Motor