Parts for Aquabot Aquamax Jr. HT Robotic Pool Cleaner,Aquamax Jr. HT parts,discount Aquabot Aquamax Jr. HT pool cleaner parts

Aquabot Jr. HT Swimming Pool Cleaner Parts Diagram

Aquabot Jr. HT Pool Cleaner Parts, Parts for Aquabot HT Pool Cleaners, Aquabot Spares
Schematic Diagram of Parts for Aquabot AquaMax Jr. HT Robotic Pool Cleaner

No.	Mfr. No.	Item No.	Description	Price
1	A10000B	ZAQP5121	Handle Assembly (Blue & White, Bracket included) -Aquabot/ Turbo/ Plus RC, AquaMax Jr. - 1 per machine	$86.57
2	S1100B	ZAQP5205	Handle Bracket (Blue) - 2 per machine -All Aquabot except T2 & T4, All AquaMax	$31.69
4	11003	ZAQP5000	Clevis Pin (Round Head, Hole in End) - 2 per machine -Use to link the Handle Assembly arm to the Handle Bracket	$4.77
6	11004	ZAQP5001	Washer (St. Steel) - 2 per machine -Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket	$1.68
7	11005	ZAQP5002	Cotter Ring (Aluminum, 3/16") - 2 per machine -Use at end of the Clevis Pin to hold the Handle Bracket	$1.68
8	1105	ZAQP5003	Screw (10-32, 7/8", S.S. Phil Pan Head) -Use to fasten the Handle Bracket to the Body Assembly	$2.56
10	2500	ZAQP5043	Screw (Old Models, #8, 1-1/4" Pan Head) - 2 per machine -Use on Back Plate Block, and for White Drive Motors through Handle Assembly	$2.56
12	2100	ZAQP5018	P-Clip (1/4", Plastic) - 1 per machine -Use to fasten the non-foam-insulated part of a 2-wire cable to the Body	$2.56
12	2102	ZAQP5020	P-Clip (7/16", Plastic) - 2 per machine -Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly	$2.56
12	8316	---	P-Clip (9/16", Plastic) -Use to fasten the Heat Shrink part of a 2-wire cable to the Handle Assembly	NLA	No Longer Available
13	2700	ZAQP5048	Screws (#8, 11/16", Phil Pan-Flat Head) - 4 per machine -Use to fasten P-Clips, Side Plates, and Drive Motors	$2.56
14	2260	ZAQP5037	Screws (#6, 7/16", Phil Pan-Flat Head) -Use to fasten P-Clips, Side Plates, H-Float and Outlet Top - 11 per machine	$2.56
15	1601	ZAQP5007	Plug (3-Pin, Female, 2-Wire) - 1 per machine -Aquabot / Turbo / T2, AquaMax, AquaMax Jr.	$16.27
---	A1629	---	Cable Assembly (for Tank Demo, 2-Wire, 10 Foot, Floating) -Aquabot / Turbo, AquaMax Junior HT / Plus	NLA	No Longer Available
17	S1675CP	ZAQP5245	Cable Assembly (2-Wire, 75 Ft., Floating) - 1 per machine	$271.57
25	2230B	ZAQP5033	Outlet Top (Blue, Plastic, Top and Bottom) - 2 per machine -Aquabot / Turbo / Plus / RC / Ultra, AquaMax / Jr. / Bi turbo	$27.56
26	A22000	ZAQP5137	Body Assembly (White, with Lock Tabs, Pin, Inserts) - 1 per machine -Aquabot / Turbo, AquaMax Jr.	$184.87
27	2251	ZAQP5035	Screw (8-18 x 3/4, Phil Small Head) -Use for Pump to Body - 4 per machine	$2.56
29	SP2300	---	Anti-Roll Brackets (Plastic, White) NLA - Replace with SK2300 Below	NLA	No Longer Available
29	SK2300	ZAQP5249	SK Bracket, Anti-Roll, White, 4 PK	$13.09
30	SP3402	---	Lock-Nuts (Hex, Nylon insert) - For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly	NLA	No Longer Available
30	3402	---	Nut, S/S, Hex Lock M5 - Set of 8	NLA	No Longer Available
31	2261	ZAQP5038	Screw (M-5, Phil Bev Head) - 4 per machine -Use to fasten the Anti-Roll Brackets to the Body Assembly	$2.56
36	SP9204BL	---	Lock-Tabs (Blue, Plastic) NLA - Replace with 9204N Below	NLA	No Longer Available
36	9204N	ZAQP5250	Lock Tab, Plastic, Natural	$3.60
38	2303	ZAQP5040	Screws (18-8, 8/32" x 1/2:, Phil Bev Head) -Use to fasten the Lock-Tabs to the Body Assembly	$2.56
39	7133	ZAQP5094	Lock-Nut (Nylon Insert, Hex) - 2 per machine -Use to fasten the Screws of the Lock-Tabs	$1.68
45	SK3400B6H	ZAQP5059	SK Side Plate, Blue, 6 Holes NLA, Replaced by SK3400B6 Below	NLA	No Longer Available
45	SK3400B6	ZAQP5251	Side Plate - Blue, 6 Holes: 4 Bolts, 2 Motor	$27.56
49	3401	ZAQP5060	Screws (S/S, PH-PN, 10-32 x 2.108, Bolts, Long, for Side Plate - Set of 8 Screws) -Aquabot Plus RC, Aquabot Ultra, All AquaMax	$2.40
51	2600	ZAQP5044	Bushing (White, Plastic, For Pulley Assembly) - 6 PER MACHINE	$4.60
52	2610	ZAQP5047	Bushing (White, Plastic, Use for Pin on Body Assembly) - 1 per machine	$6.66
54	3500	ZAQP5062	Small Roller (White, Plastic) - 4 per machine -Supports the Drive Track, install on lower legs of Side Plate	$4.60
55	3700	ZAQP5067	Large Roller (White, Plastic) - 1 per machine -Supports the Drive Track, installs on Body Assembly Pin Support	$6.00
56	3506	ZAQP5064	STEPPED SLEEVE ROLLER (White, Install on upper Sideplate legs, thick end supports Belts) - 2 per machine	$4.60
57	SP3302	ZAQP0005	Single AquaBot Drive Belt (Tan, Small)	$10.47
58	A3600	ZAQP5150	Pulley Assembly (Short, ~ 2.5 in., includes 2 washers) -Use for cleaners with White Drive Motors - 1 per machine	$25.44
---	SP3502	---	Tension Device (Old, Replaced by Stepped Sleeve Rollers) -Formerly used to add Tension to Drive Belts	NLA	No Longer Available
60	A6001T	ZAQP5174	Pump Motor (Includes propeller) - 1 per machine -Aquabot Turbo, Aquabot Tempo, AquaMax Jr. Ht	$263.12
60	A6010U	---	Pump Motor (Old design, no Impeller or Jet Nozzles) - 1 per machine NLA, Obsolete - Replaced by SA69007 Below	NLA	No Longer Available
60	SA69007	ZAQP5253	Pump Motor (Includes propeller) - 2 per machine formerly A6010U, installation kit included	$356.89
61	4400	---	Propeller (Pushes onto Pump Motor Shaft) - 1 per machine	$13.62
65	A2207	---	DC Pump Filter (White, Plastic) -Aquabot Turbo Solo/ Turbo RC, All AquaMax RC / Solo cleaners	NLA	No Longer Available
66	300099	ZAQP5052	Tubing (Clear PVC, 5/16" ID x 7/16" OD) -Use to divert water from the DC Pump Filter to the DC Pump	$2.20
67	700038	ZAQP5077	Spacer Block (Gray, Stepped shape) -Use to position the Piston apart from the Model g Drive Tracks	$11.76
68	S300092	---	DC Pump Motor (Single, no Gate, 2-Wire) -Aquabot Turbo Solo, All AquaMax Solo/ IR cleaners	NLA	No Longer Available
68	S300093	---	DC Pump Motor (Dual, with Gate, 2-Wire) -Aquabot Turbo RC, Aquabot T4, All AquaMax RC cleaners	NLA	No Longer Available
69	300111	---	Tubing (Clear PVC, 3/16" ID x 5/16" OD) -Use to divert water from the DC Pump to the Piston Assembly	NLA	No Longer Available
70	300109	---	Clamp (Gray, Plastic, Narrow) -Aquabot Turbo Solo / RC / T4, All AquaMax RC / Solo cleaners	NLA	No Longer Available
70	300108	---	Clamp Bracket (Gray, Plastic, Wide) -Aquabot Turbo Solo / RC, All AquaMax RC / Solo cleaners	NLA	No Longer Available
71	300107	---	Back Plate Block (Gray, 4 holes) -Use to Support the DC Pump Motor inside of the Body Assembly	NLA	No Longer Available
72	SP6204	---	Spacer (Plastic, cylinder) -Use to make space between the Back Plate Block and the Body Assembly	NLA	No Longer Available
73	2301	---	Screw (10-32, 1/2" Phil Pan Head) -Use with Clamp to fasten Piston to Side Plate and DC Pump to Block	NLA	No Longer Available
77	S300090	ZAQP5209	Piston Assembly (White, Plastic) -One Piston is used for Solo Cleaners, Two are used for RC cleaners	$57.23
78	300084	---	Rubber Tip (White, Rubber) -Use at the bottom of the plunger of the Piston Assembly	NLA	No Longer Available
80	A4510D	---	Drive Motor (White, Terminal Basin, for Tank Demo unit) -Aquabot / Aquabot Turbo Tank Demo	NLA	No Longer Available
80	SA59010	ZAQP5163	Drive Motor (White, Terminal Basin) -AquaMax Jr. HT	$403.69
80	A8411IR	---	Drive Motor (Black, bare wire leads) -AquaMax Jr. Plus IR	NLA	No Longer Available
80	A8516MBTS	---	>Drive Motor (Black, bare wire leads) -AquaMax Jr. Plus Solo	NLA	No Longer Available
81	4619	ZAQP5072	Loop Connector (Metal, Crimp on wire) - set of 2 -Use to attach wires to Brass Terminals on White Drive Motor	$3.20
82	4618	ZAQP5071	Brass Nuts (Hex, Small) - 2 per machine -Use for attaching the Loop Connectors of wires to Brass Terminals	$2.56
83	4613	ZAQP5070	Spiral Pin (3/4", Solid Stainless Steel) - 1 per machine -Used in the end of the Drive Motor shaft, use Lock-Tite	$2.56
---	800001	ZAQP5105	Putty (Gray, Waterproof) - 1/8 per machine -For waterproofing the Terminal Basin in all White Drive Motors, pack tight and seal cover	$11.04
84	5000	ZAQP5073	Terminal Cover (Plastic, Rectangle) - 1 per machine -For covering the Basin in all White Drive Motors	$4.07
85	4501	ZAQP5069	Screw (8-18 x 1/2, Phil Pan Head) - 1 per machine -Use to fasten the Terminal Cover and the Extension Brackets	$2.56
---	SP1611	---	Shrink Tube (3/4", Blue) -For sealing the Cable insulation below the P-Clip at the Handle Assembly	NLA	No Longer Available
---	A38205	---	Wheel Tube Assembly (Old) -AquaMax Jr. HT, AquaMax Jr. Plus	NLA	No Longer Available
90	A38205MG	ZAQP5160	Wheel Tube Assembly - 2 per machine	$58.28
91	11058	ZAQP5260	Retaining Ring (E-Clip, New Style) - 4 per machine -Aquabot Turbo, AB Plus RC, Aquabot T4, All AMAX	$6.13
92	3603	ZAQP5065	Washer (Nylon, Flat) - 4 per machine -Use for all cleaners on the end of Wheel or Wheel Tube Assembly	$2.56
97	3002B	ZAQP0001	Aquabot Molded Rubber Brush - blue, 12"	$31.47
97	SP3003B	---	Rubber Brushes (Black Molded Rubber, Short) -Aquabot / Turbo / T4, AquaMax Jr. units, Ultramax ***	NLA	No Longer Available
97	3009	ZAQP5261	PVA Climbing Brushes (Light Blue PVA Foam, Short, 26.5 CM) -Aquabot / Turbo, AquaMax Jr. HT units, Ultramax ***	$53.33
97	A38205PVA	ZAQP5257	Wheel Tube Assembly, AB, 12" W/ PVA	$87.62
---	SP3007	ZAQP5228	PVA Climbing Rings (Light Blue PVA, 1" Thick) -Fit over Rubber Brushes to add more traction**	$7.42
99	3200	ZAQP5056	Drive Track (Black)	$24.71
99	3203	ZAQP5057	Drive Track with Traction Tabs (Blue) -For all Model 'G' units - single	$24.71
100	SP2675	---	Model Spacer Brackets - necessary with Model 'G' Drive Tracks NLA - Replace with SK2675 Below**	NLA	No Longer Available
100	SK2675	ZAQP5259	Model G Spacer Brackets 2 x 2 PK	$6.97
101	8100	---	Filter Bag (Fine) NLA - Replace with 8111 Below	NLA	No Longer Available
101	8111	ZAQP0003	Filter Bag (Small, Fine) - 1 per machine -Aquabot / Turbo / Plus RC, AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **	$41.97
101	8200	ZAQP0004	Aquabot Filter Bag (Mesh)	$52.47
101	8112	ZAQP5264	Filter Bag (Optional, Small, Mesh Filter Bag) - 1 per machine	$42.51
103	AP5300	---	Filter Screen (White, Cage) - 1 per machine -Aquabot / Turbo / Plus RC, AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **	NLA	No Longer Available
104	2702	ZAQP5050	Screw (#6, 11/16", Phil Pan-Flat Head, Pointed) -For fastening the Filter Screen to the Body - 2 per machine	$2.56
105	A9200X	ZAQP5196	Bottom Lid Assembly (White, W-Shaped Wire Frame)- 1 per machine -Aquabot, small Jet / Rover, AquaMax Jr., UltraMax ***	$76.77
106	9305BB	ZAQP5265	Intake Valve Flap (Blue Plastic) Fits into Intake of Bottom Lid - 2 per machine	$7.67
108	S3103	ZAQP5212	H-Float (Foam, Plastic, with Screws) - Fasten to Bottom Lid if cleaner's wall-climbing is not high enough	$12.93
---	SP5173	---	Weights (Black) - Put in Bottom Lid if cleaner's wall climbing is too high, or to help JetMax / Jr. sink to floor	NLA	No Longer Available
109	3104	ZAQP5055	Side Pocket Floats (White, Foam Blocks) -Put in Bottom Lid if wall-climbing is not high enough	$3.72
110	7063C	ZAQP5084	Power Supply (3-Prong, Male Socket) - 1 per machine -AquaMax Jr. HT, AquaMax Jr. Plus, AquaMax, PHV 100	$286.08
110	A7082	---	Power Supply (4-Prong, Male Socket) -AquaMax Jr. Plus RC, AquaMax RC	NLA	No Longer Available
111	7108	ZAQP5091	Socket Assembly (3-Pin, Male, 2-Wire) -Aquabot / Turbo / T2, All Jet and Rover cleaners, AquaMax / Jr.	$11.67
112	7005	ZAQP5079	Fuse Holder (Standard, Push & Turn Style) - 1 on Power Supply -Most Residential and Commercial cleaners	$9.04
112	7205	ZAQP5100	Fuse Holder (Alternate, Phillips Head Style) - 1 on Power Supply -Only when specified by Aqua Products Service	$9.04
114	7106	ZAQP5090	Wide Switch (11/4" x 3/4", Red, 3-Wire) -Use for Power Supply without Dial Timer	$9.07
117	7041A	ZAQP5083	Handle (Soft Plastic, with Hardware) -Use on All Power Supplies except UltraMax	$8.91
118	7102	ZAQP5089	Cord for Power Supply (3-Wire, Green, Black, and White) -Use on all Power Supplies	$12.96
119	7272	ZAQP5103	Outdoor Timer (8hr, Programmable, GFCI) - 1 per machine -Use to regulate cleaner's run time when no Auto shut-off	$42.35
---	1609	---	Tie (Blue, #4 Plastic, Reusable) -Use for coiling the Cable Assembly among other things	NLA	No Longer Available
---	A800135	ZAQP5185	Main Drain Bumper -Can be used on most Pools' Main Drain, where a cleaner may get stuck	$36.62

All Aquabot Junior HT Cleaner Parts are Original Aquabot Replacement Parts, and spares for the Aquabot
To purchase more than 1 (one) Aquabot Jr. HT part, hit the		button in the Shopping Cart.


	Return to POOLCENTER.com's Swimming Pool Cleaner Parts Main Page

Aquabot Jr. HT Swimming Pool Cleaner Parts Diagram

Aquabot Jr. HT Pool Cleaner Parts, Parts for Aquabot HT Pool Cleaners, Aquabot Spares Schematic Diagram of Parts for Aquabot AquaMax Jr. HT Robotic Pool Cleaner

Handle Assembly (Blue & White, Bracket included) -Aquabot/ Turbo/ Plus RC, AquaMax Jr. - 1 per machine

Handle Bracket (Blue) - 2 per machine -All Aquabot except T2 & T4, All AquaMax

Clevis Pin (Round Head, Hole in End) - 2 per machine -Use to link the Handle Assembly arm to the Handle Bracket

Washer (St. Steel) - 2 per machine -Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket

Cotter Ring (Aluminum, 3/16") - 2 per machine -Use at end of the Clevis Pin to hold the Handle Bracket

Screw (10-32, 7/8", S.S. Phil Pan Head) -Use to fasten the Handle Bracket to the Body Assembly

Screw (Old Models, #8, 1-1/4" Pan Head) - 2 per machine -Use on Back Plate Block, and for White Drive Motors through Handle Assembly

P-Clip (1/4", Plastic) - 1 per machine -Use to fasten the non-foam-insulated part of a 2-wire cable to the Body

P-Clip (7/16", Plastic) - 2 per machine -Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly

P-Clip (9/16", Plastic) -Use to fasten the Heat Shrink part of a 2-wire cable to the Handle Assembly

Screws (#8, 11/16", Phil Pan-Flat Head) - 4 per machine -Use to fasten P-Clips, Side Plates, and Drive Motors

Screws (#6, 7/16", Phil Pan-Flat Head) -Use to fasten P-Clips, Side Plates, H-Float and Outlet Top - 11 per machine

Plug (3-Pin, Female, 2-Wire) - 1 per machine -Aquabot / Turbo / T2, AquaMax, AquaMax Jr.

Cable Assembly (for Tank Demo, 2-Wire, 10 Foot, Floating) -Aquabot / Turbo, AquaMax Junior HT / Plus

Cable Assembly (2-Wire, 75 Ft., Floating) - 1 per machine

Outlet Top (Blue, Plastic, Top and Bottom) - 2 per machine -Aquabot / Turbo / Plus / RC / Ultra, AquaMax / Jr. / Bi turbo

Body Assembly (White, with Lock Tabs, Pin, Inserts) - 1 per machine -Aquabot / Turbo, AquaMax Jr.

Screw (8-18 x 3/4, Phil Small Head) -Use for Pump to Body - 4 per machine

Anti-Roll Brackets (Plastic, White) NLA - Replace with SK2300 Below

SK Bracket, Anti-Roll, White, 4 PK

Lock-Nuts (Hex, Nylon insert) - For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly

Nut, S/S, Hex Lock M5 - Set of 8

Screw (M-5, Phil Bev Head) - 4 per machine -Use to fasten the Anti-Roll Brackets to the Body Assembly

Lock-Tabs (Blue, Plastic) NLA - Replace with 9204N Below

Lock Tab, Plastic, Natural

Screws (18-8, 8/32" x 1/2:, Phil Bev Head) -Use to fasten the Lock-Tabs to the Body Assembly

Lock-Nut (Nylon Insert, Hex) - 2 per machine -Use to fasten the Screws of the Lock-Tabs

SK Side Plate, Blue, 6 Holes NLA, Replaced by SK3400B6 Below

Side Plate - Blue, 6 Holes: 4 Bolts, 2 Motor

Screws (S/S, PH-PN, 10-32 x 2.108, Bolts, Long, for Side Plate - Set of 8 Screws) -Aquabot Plus RC, Aquabot Ultra, All AquaMax

Bushing (White, Plastic, For Pulley Assembly) - 6 PER MACHINE

Bushing (White, Plastic, Use for Pin on Body Assembly) - 1 per machine

Small Roller (White, Plastic) - 4 per machine -Supports the Drive Track, install on lower legs of Side Plate

Large Roller (White, Plastic) - 1 per machine -Supports the Drive Track, installs on Body Assembly Pin Support

STEPPED SLEEVE ROLLER (White, Install on upper Sideplate legs, thick end supports Belts) - 2 per machine

Single AquaBot Drive Belt (Tan, Small)

Pulley Assembly (Short, ~ 2.5 in., includes 2 washers) -Use for cleaners with White Drive Motors - 1 per machine

Tension Device (Old, Replaced by Stepped Sleeve Rollers) -Formerly used to add Tension to Drive Belts

Pump Motor (Includes propeller) - 1 per machine -Aquabot Turbo, Aquabot Tempo, AquaMax Jr. Ht

Pump Motor (Old design, no Impeller or Jet Nozzles) - 1 per machine NLA, Obsolete - Replaced by SA69007 Below

Pump Motor (Includes propeller) - 2 per machine formerly A6010U, installation kit included

Propeller (Pushes onto Pump Motor Shaft) - 1 per machine

DC Pump Filter (White, Plastic) -Aquabot Turbo Solo/ Turbo RC, All AquaMax RC / Solo cleaners

Tubing (Clear PVC, 5/16" ID x 7/16" OD) -Use to divert water from the DC Pump Filter to the DC Pump

Spacer Block (Gray, Stepped shape) -Use to position the Piston apart from the Model g Drive Tracks

DC Pump Motor (Single, no Gate, 2-Wire) -Aquabot Turbo Solo, All AquaMax Solo/ IR cleaners

DC Pump Motor (Dual, with Gate, 2-Wire) -Aquabot Turbo RC, Aquabot T4, All AquaMax RC cleaners

Tubing (Clear PVC, 3/16" ID x 5/16" OD) -Use to divert water from the DC Pump to the Piston Assembly

Clamp (Gray, Plastic, Narrow) -Aquabot Turbo Solo / RC / T4, All AquaMax RC / Solo cleaners

Clamp Bracket (Gray, Plastic, Wide) -Aquabot Turbo Solo / RC, All AquaMax RC / Solo cleaners

Back Plate Block (Gray, 4 holes) -Use to Support the DC Pump Motor inside of the Body Assembly

Spacer (Plastic, cylinder) -Use to make space between the Back Plate Block and the Body Assembly

Screw (10-32, 1/2" Phil Pan Head) -Use with Clamp to fasten Piston to Side Plate and DC Pump to Block

Piston Assembly (White, Plastic) -One Piston is used for Solo Cleaners, Two are used for RC cleaners

Rubber Tip (White, Rubber) -Use at the bottom of the plunger of the Piston Assembly

Drive Motor (White, Terminal Basin, for Tank Demo unit) -Aquabot / Aquabot Turbo Tank Demo

Drive Motor (White, Terminal Basin) -AquaMax Jr. HT

Drive Motor (Black, bare wire leads) -AquaMax Jr. Plus IR

>Drive Motor (Black, bare wire leads) -AquaMax Jr. Plus Solo

Loop Connector (Metal, Crimp on wire) - set of 2 -Use to attach wires to Brass Terminals on White Drive Motor

Brass Nuts (Hex, Small) - 2 per machine -Use for attaching the Loop Connectors of wires to Brass Terminals

Spiral Pin (3/4", Solid Stainless Steel) - 1 per machine -Used in the end of the Drive Motor shaft, use Lock-Tite

Putty (Gray, Waterproof) - 1/8 per machine -For waterproofing the Terminal Basin in all White Drive Motors, pack tight and seal cover

Terminal Cover (Plastic, Rectangle) - 1 per machine -For covering the Basin in all White Drive Motors

Screw (8-18 x 1/2, Phil Pan Head) - 1 per machine -Use to fasten the Terminal Cover and the Extension Brackets

Shrink Tube (3/4", Blue) -For sealing the Cable insulation below the P-Clip at the Handle Assembly

Wheel Tube Assembly (Old) -AquaMax Jr. HT, AquaMax Jr. Plus

Wheel Tube Assembly - 2 per machine

Retaining Ring (E-Clip, New Style) - 4 per machine -Aquabot Turbo, AB Plus RC, Aquabot T4, All AMAX

Washer (Nylon, Flat) - 4 per machine -Use for all cleaners on the end of Wheel or Wheel Tube Assembly

Aquabot Molded Rubber Brush - blue, 12"

Rubber Brushes (Black Molded Rubber, Short) -Aquabot / Turbo / T4, AquaMax Jr. units, Ultramax ***

PVA Climbing Brushes (Light Blue PVA Foam, Short, 26.5 CM) -Aquabot / Turbo, AquaMax Jr. HT units, Ultramax ***

Wheel Tube Assembly, AB, 12" W/ PVA

PVA Climbing Rings (Light Blue PVA, 1" Thick) -Fit over Rubber Brushes to add more traction**

Drive Track (Black)

Drive Track with Traction Tabs (Blue) -For all Model 'G' units - single

Model Spacer Brackets - ** necessary with Model 'G' Drive Tracks NLA - Replace with SK2675 Below

Aquabot Jr. HT Pool Cleaner Parts, Parts for Aquabot HT Pool Cleaners, Aquabot Spares
Schematic Diagram of Parts for Aquabot AquaMax Jr. HT Robotic Pool Cleaner

Handle Assembly (Blue & White, Bracket included)
-Aquabot/ Turbo/ Plus RC, AquaMax Jr. - 1 per machine

Handle Bracket (Blue) - 2 per machine
-All Aquabot except T2 & T4, All AquaMax

Clevis Pin (Round Head, Hole in End) - 2 per machine
-Use to link the Handle Assembly arm to the Handle Bracket

Washer (St. Steel) - 2 per machine
-Use around the Clevis Pin underneath the Cotter Ring on Handle Assembly Bracket

Cotter Ring (Aluminum, 3/16") - 2 per machine
-Use at end of the Clevis Pin to hold the Handle Bracket

Screw (10-32, 7/8", S.S. Phil Pan Head)
-Use to fasten the Handle Bracket to the Body Assembly

Screw (Old Models, #8, 1-1/4" Pan Head) - 2 per machine
-Use on Back Plate Block, and for White Drive Motors through Handle Assembly

P-Clip (1/4", Plastic) - 1 per machine
-Use to fasten the non-foam-insulated part of a 2-wire cable to the Body

P-Clip (7/16", Plastic) - 2 per machine
-Use to fasten the foam-insulated part of a 2-wire cable to the Handle Assembly

P-Clip (9/16", Plastic)
-Use to fasten the Heat Shrink part of a 2-wire cable to the Handle Assembly

Screws (#8, 11/16", Phil Pan-Flat Head) - 4 per machine
-Use to fasten P-Clips, Side Plates, and Drive Motors

Screws (#6, 7/16", Phil Pan-Flat Head)
-Use to fasten P-Clips, Side Plates, H-Float and Outlet Top - 11 per machine

Plug (3-Pin, Female, 2-Wire) - 1 per machine
-Aquabot / Turbo / T2, AquaMax, AquaMax Jr.

Cable Assembly (for Tank Demo, 2-Wire, 10 Foot, Floating)
-Aquabot / Turbo, AquaMax Junior HT / Plus

Cable Assembly (2-Wire, 75 Ft., Floating)
- 1 per machine

Outlet Top (Blue, Plastic, Top and Bottom) - 2 per machine
-Aquabot / Turbo / Plus / RC / Ultra, AquaMax / Jr. / Bi turbo

Body Assembly (White, with Lock Tabs, Pin, Inserts) - 1 per machine
-Aquabot / Turbo, AquaMax Jr.

Screw (8-18 x 3/4, Phil Small Head)
-Use for Pump to Body - 4 per machine

Anti-Roll Brackets (Plastic, White)
NLA - Replace with SK2300 Below

Lock-Nuts (Hex, Nylon insert)
- For various uses: Side Plate Bolts, Anti-Roll Brackets, Pole Handle Assembly

Screw (M-5, Phil Bev Head) - 4 per machine
-Use to fasten the Anti-Roll Brackets to the Body Assembly

Lock-Tabs (Blue, Plastic)
NLA - Replace with 9204N Below

Screws (18-8, 8/32" x 1/2:, Phil Bev Head)
-Use to fasten the Lock-Tabs to the Body Assembly

Lock-Nut (Nylon Insert, Hex) - 2 per machine
-Use to fasten the Screws of the Lock-Tabs

SK Side Plate, Blue, 6 Holes
NLA, Replaced by SK3400B6 Below

Screws (S/S, PH-PN, 10-32 x 2.108, Bolts, Long, for Side Plate - Set of 8 Screws)
-Aquabot Plus RC, Aquabot Ultra, All AquaMax

Small Roller (White, Plastic) - 4 per machine
-Supports the Drive Track, install on lower legs of Side Plate

Large Roller (White, Plastic) - 1 per machine
-Supports the Drive Track, installs on Body Assembly Pin Support

STEPPED SLEEVE ROLLER (White, Install on upper
Sideplate legs, thick end supports Belts) - 2 per machine

Pulley Assembly (Short, ~ 2.5 in., includes 2 washers)
-Use for cleaners with White Drive Motors - 1 per machine

Tension Device (Old, Replaced by Stepped Sleeve Rollers)
-Formerly used to add Tension to Drive Belts

Pump Motor (Includes propeller) - 1 per machine
-Aquabot Turbo, Aquabot Tempo, AquaMax Jr. Ht

Pump Motor (Old design, no Impeller or Jet Nozzles) - 1 per machine
NLA, Obsolete - Replaced by SA69007 Below

Pump Motor (Includes propeller) - 2 per machine
formerly A6010U, installation kit included

DC Pump Filter (White, Plastic)
-Aquabot Turbo Solo/ Turbo RC, All AquaMax RC / Solo cleaners

Tubing (Clear PVC, 5/16" ID x 7/16" OD)
-Use to divert water from the DC Pump Filter to the DC Pump

Spacer Block (Gray, Stepped shape)
-Use to position the Piston apart from the Model g Drive Tracks

DC Pump Motor (Single, no Gate, 2-Wire)
-Aquabot Turbo Solo, All AquaMax Solo/ IR cleaners

DC Pump Motor (Dual, with Gate, 2-Wire)
-Aquabot Turbo RC, Aquabot T4, All AquaMax RC cleaners

Tubing (Clear PVC, 3/16" ID x 5/16" OD)
-Use to divert water from the DC Pump to the Piston Assembly

Clamp (Gray, Plastic, Narrow)
-Aquabot Turbo Solo / RC / T4, All AquaMax RC / Solo cleaners

Clamp Bracket (Gray, Plastic, Wide)
-Aquabot Turbo Solo / RC, All AquaMax RC / Solo cleaners

Back Plate Block (Gray, 4 holes)
-Use to Support the DC Pump Motor inside of the Body Assembly

Spacer (Plastic, cylinder)
-Use to make space between the Back Plate Block and the Body Assembly

Screw (10-32, 1/2" Phil Pan Head)
-Use with Clamp to fasten Piston to Side Plate and DC Pump to Block

Piston Assembly (White, Plastic)
-One Piston is used for Solo Cleaners, Two are used for RC cleaners

Rubber Tip (White, Rubber)
-Use at the bottom of the plunger of the Piston Assembly

Drive Motor (White, Terminal Basin, for Tank Demo unit)
-Aquabot / Aquabot Turbo Tank Demo

Drive Motor (White, Terminal Basin)
-AquaMax Jr. HT

Drive Motor (Black, bare wire leads)
-AquaMax Jr. Plus IR

>Drive Motor (Black, bare wire leads)
-AquaMax Jr. Plus Solo

Loop Connector (Metal, Crimp on wire) - set of 2
-Use to attach wires to Brass Terminals on White Drive Motor

Brass Nuts (Hex, Small) - 2 per machine
-Use for attaching the Loop Connectors of wires to Brass Terminals

Spiral Pin (3/4", Solid Stainless Steel) - 1 per machine
-Used in the end of the Drive Motor shaft, use Lock-Tite

Putty (Gray, Waterproof) - 1/8 per machine
-For waterproofing the Terminal Basin in all White Drive Motors, pack tight and seal cover

Terminal Cover (Plastic, Rectangle) - 1 per machine
-For covering the Basin in all White Drive Motors

Screw (8-18 x 1/2, Phil Pan Head) - 1 per machine
-Use to fasten the Terminal Cover and the Extension Brackets

Shrink Tube (3/4", Blue)
-For sealing the Cable insulation below the P-Clip at the Handle Assembly

Wheel Tube Assembly (Old)
-AquaMax Jr. HT, AquaMax Jr. Plus

Retaining Ring (E-Clip, New Style) - 4 per machine
-Aquabot Turbo, AB Plus RC, Aquabot T4, All AMAX

Washer (Nylon, Flat) - 4 per machine
-Use for all cleaners on the end of Wheel or Wheel Tube Assembly

Rubber Brushes (Black Molded Rubber, Short)
-Aquabot / Turbo / T4, AquaMax Jr. units, Ultramax ***

PVA Climbing Brushes (Light Blue PVA Foam, Short, 26.5 CM)
-Aquabot / Turbo, AquaMax Jr. HT units, Ultramax ***

PVA Climbing Rings (Light Blue PVA, 1" Thick)
-Fit over Rubber Brushes to add more traction**

Drive Track with Traction Tabs (Blue)
-For all Model 'G' units - single

Model Spacer Brackets - necessary with Model 'G' Drive Tracks
NLA - Replace with SK2675 Below**

Filter Bag (Fine)
NLA - Replace with 8111 Below

Filter Bag (Small, Fine) - 1 per machine
-Aquabot / Turbo / Plus RC, AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **

Filter Screen (White, Cage) - 1 per machine
-Aquabot / Turbo / Plus RC, AquaMax Jr., PHV 100/300, small Jet / Rover, UMAX **

Screw (#6, 11/16", Phil Pan-Flat Head, Pointed)
-For fastening the Filter Screen to the Body - 2 per machine

Bottom Lid Assembly (White, W-Shaped Wire Frame)- 1 per machine
-Aquabot, small Jet / Rover, AquaMax Jr., UltraMax ***

Intake Valve Flap (Blue Plastic)
Fits into Intake of Bottom Lid - 2 per machine

H-Float (Foam, Plastic, with Screws)
- Fasten to Bottom Lid if cleaner's wall-climbing is not high enough

Weights (Black) - Put in Bottom Lid if cleaner's wall climbing
is too high, or to help JetMax / Jr. sink to floor

Side Pocket Floats (White, Foam Blocks)
-Put in Bottom Lid if wall-climbing is not high enough

Power Supply (3-Prong, Male Socket) - 1 per machine
-AquaMax Jr. HT, AquaMax Jr. Plus, AquaMax, PHV 100

Power Supply (4-Prong, Male Socket)
-AquaMax Jr. Plus RC, AquaMax RC

Socket Assembly (3-Pin, Male, 2-Wire)
-Aquabot / Turbo / T2, All Jet and Rover cleaners, AquaMax / Jr.

Fuse Holder (Standard, Push & Turn Style) - 1 on Power Supply
-Most Residential and Commercial cleaners